- 1 How do I know my bike chain size?
- 2 How do I know what size mountain bike chain I need?
- 3 How do I know my chain size?
- 4 What bicycle chain do I need?
- 5 What size is standard bicycle chain?
- 6 How often should I change my bike chain?
- 7 Are 7 and 8 speed chains the same?
- 8 How do I know my roller chain size?
- 9 Is it OK to use wd40 on bike chain?
- 10 How do I know if my bike chain is too short?
- 11 Are 11 and 12 speed chains the same?
How do I know my bike chain size?
Add the multiplied chainstay length, the divided number of teeth for the chainring and rear sprocket, and add 1 (or 2.5 cm). The result is the ideal chain length for your bike. For example, you’d add 32.5, 13, 7 and 1 to get 53.5. The length of the chain should be 53.5 inches or 135.89 cm.
How do I know what size mountain bike chain I need?
Begin by counting the number of teeth on the largest front sprocket and largest rear. These numbers are often printed right on the sprockets and cogs. Next, measure the distance between the middle of the crank bolt to the rear axle. This is also the chain stay length.
How do I know my chain size?
To measure the chain size, if you have just the sprocket, use calipers to measure between the teeth. Measure from center to center of where the chain roller would set between the teeth that will give you the pitch. Once you know the pitch you can determine what chain size you would need.
What bicycle chain do I need?
How do I choose? Bike chain selection is firstly decided based upon the “speed” of the chain; this is because it determines the width of the chain. An 11 speed chain for example is narrower than a 9 speed chain, as the sprockets on the 11 speed cassette have a narrower spacing between them.
What size is standard bicycle chain?
Chains come in 3⁄32 in (2.4 mm), 1⁄8 in (3.2 mm), 5⁄32 in (4.0 mm), or 3⁄16 in (4.8 mm) roller widths, the internal width between the inner plates. 1⁄8 in (3.2 mm) chains are typically used on bikes with a single rear sprocket: those with coaster brakes, hub gears, fixed gears such as track bicycles, or BMX bikes.
How often should I change my bike chain?
The 2,000-Mile Rule. To avoid this accelerated wear of your cassette and chainrings, a general rule of thumb is to replace your bike’s chain every 2,000 miles. Mind you, this is just a starting point. No two chains will wear at exactly the same rate because no two riders treat their chains the same.
Are 7 and 8 speed chains the same?
5, 6, 7 and 8 speed chains Shimano, SRAM and Campagnolo all use the same chain with 8 speeds. Chain for 7 speeds is a bit wider – 7.3 mm, while a 6 speed one is substantially wider – 7.8 mm. Going further narrower, like a 10, or 11 speed chain on an 8 speed cassette can and often does work.
How do I know my roller chain size?
Roller Chain Identification Most roller chain has the size stamped right into the side plates. You may see something like “40”, “C2080H” or “10B” stamped in, which the industry number that represents the chain size. Old chains will most likely need to be cleaned in order to see the size.
Is it OK to use wd40 on bike chain?
You can use WD-40 Multi-Use- Product. It is a water based lubricant that provides the right amount of lubrication to the chain lube. WD-40 is a great bike chain lube water based lubricant and will not only lubricate the chain well, but will also keep it rust and corrosion free.
How do I know if my bike chain is too short?
You should also see two slight bends at each jockey wheel of the rear derailleur. If the chain is too short, this shift is difficult to make and the derailleur cage is stretched out and almost parallel to the chainstay. If the chain is really short, then you might not even be able to shift into the largest cog.
Are 11 and 12 speed chains the same?
12-speed chains can operate just fine with 11-speed cassettes. The main exception are Shimano’s new 12-speed HG+ models which are heavily optimized for downshifting and thus come with custom inner plates that don’t mix well with non-Shimano 12-speed components.